Full Project – Design and construction of a 0-24v variable regulated power supply

Click here to Get this Complete Project Chapter 1-5

ABSTRACT

This project work is on design of a variable regulated power supply. This work describes you how to design a variable regulated power supply circuit. The main advantage of this power supply circuit is that it can vary the output voltage and output current.

A variable regulated power supply supplies different level of electric energy to an electrical load. The primary function of a variable power supply is to supply variable output voltage and output current which can be used to power devices.

TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE

DEDICATION

ACKNOWELDGEMENT

ABSTRACT

TABLE OF CONTENT

CHAPTER ONE

• INTRODUCTION
• BACKGROUND OF THE PROJECT
• PROBLEM STATEMENT
• AIM/OBJECTIVE OF THE PROJECT
• PURPOSE OF THE PROJECT
• SIGNIFICANCE OF THE PROJECT
• LIMITATION OF THE PROJECT
• APPLICATION OF THE PROJECT
• PROJECT ORGANISATION

CHAPTER TWO

LITERATURE REVIEW

2.0      LITERATURE REVIEW

2.1      REVIEW OF POWER SUPPLY

2.2     REVIEW OF POWER SUPPLY CHARACTERISTICS

2.3      REVIEW OF GENERAL APPLICATION OF POWER SUPPLY APPLICATIONS

2.4       REVIEW OF TYPES OF POWER SUPPLY

CHAPTER THREE

3.0      CONSTRUCTION METHODOLOGY

3.1      BLOCK DIAGRAM OF THE SYSTEM

3.2      BLOCK DIAGRAM DESCRIPTION

3.3      CIRCUIT DIAGRAM

3.4      CIRCUIT DESCRIPTION

3.7      SYSTEM OPERATION

3.8     CIRCUIT DESCRIPTION

3.9     DESCRIPTION OF MAJOR COMPONENTS USED

CHAPTER FOUR

4.0       RESULT ANALYSIS

4.1      CONSTRUCTION PROCEDURE AND TESTING

4.2      ASSEMBLING OF SECTIONS

4.3      CONSRUCTION OF THE CASING

4.4     TESTING

4.5     INSTALLATION OF THE COMPLETED DESIGN

CHAPTER FIVE

• CONCLUSIONS
• RECOMMENDATION
• REFERENCES

CHAPTER ONE

• INTRODUCTION

1.1                                            BACKGROUND O THE STUDY

A power supply is an electronic device that supplies electric energy to an electrical load. The primary function of a power supply is to convert one form of electrical energy to another and, as a result, power supplies are sometimes referred to as electric power converters. Some power supplies are discrete, stand-alone devices, whereas others are built into larger devices along with their loads according to US patent #4937722.

Every power supply must obtain the energy it supplies to its load, as well as any energy it consumes while performing that task, from an energy source. Depending on its design, a power supply may obtain energy from various types of energy sources, including electrical energy transmission systems, energy storage devices such as a batteries and fuel cells, electromechanical systems such as generators and alternators, solar power converters, or another power supply (Torres, 2008).

All power supplies have a power input, which receives energy from the energy source, and a power output that delivers energy to the load. In most power supplies the power input and output consist of electrical connectors or hardwired circuit connections, though some power supplies employ wireless energy transfer in lieu of galvanic connections for the power input or output. Some power supplies have other types of inputs and outputs as well, for functions such as external monitoring and control (Torres, 2008).

To obtain a complete circuit for this work, the circuit is mainly composed of the:

• Input transformer:   The input transformer is used to transform the incoming line voltage down to the required level for the power supply. Typically the input transformer provides a step down function. It also isolates the output circuit from the line supply.
• Rectifier:   The power supply rectifier converts the incoming signal from an AC format into raw DC. Either half wave or more commonly full wave rectifiers may be used as they make use of both halves of the incoming AC signal.
• Smoothing:   The raw DC from the rectifier is far from constant falling to zero when the AC waveform crossed the zero axis, and then rising to its peak. The addition of a reservoir capacitor here fills in the troughs in the waveform, enabling the next stage of the power supply to operate. Large value capacitors are normally used within this stage.
• Voltage adjuster:   This stage of the power supply takes the smoothed voltage and uses a variable ic and potentiometer to provide a variable regulated output virtually regardless of the output current and any minor fluctuations in the input level.

1.2                                                  PROBLEM STATEMENT

For prototyping and hobbyists, appliances or gadget with smaller voltages, they normally use batteries as a reliable power source. Instead of using batteries, which have a limited lifetime and which is also cost effective, a variable DC power supply can be used which is implemented in this project (Martin Kaffei, 2011).

1.3                                                   AIM OF THE PROJECT

The aim of any power supply is to provide the required power to the load using an AC supply at the input. But for variable regulated power supply of 0 – 24v is to design a power supply with one output terminal with variable output voltage, and the output is gotten by turning the voltage adjuster known as the potentiometer (Martin Kaffei, 2011).

1.4                                            LIMITATION OF THE PROJECT

This device is limited at producing from 0 – 24v output using a 30volts center tap transformer.

1.5                                          SIGNIFICANCE OF THE PROJECT

This work makes it possible for someone to use one power supply to run different devices of higher or lower voltage rating without considering buying a new or different power supply.

1.6                                           APPLICATION OF THE PROJECT

A variable regulated power supply is a regulator that electricians and electrical project hobbyists use to test the capacity of voltage for any project they may have completed. The power supply is used as a gauge to make sure the piece of work the person has completed is able to withstand certain amounts of voltage and current load. Tests are generally conducted by applying different amounts of voltage to the piece of completed work a little at a time to ensure the stability of the circuit the individual has created. These types of power supplies also are used by hobbyists to power small electronics requiring variable voltage and by tattoo artists to power tattooing guns (Torres, 2008).

By using such a variable supply of power, the individual is able to spot any temperaments or inconsistencies in the circuit he’s created in a manner that allows for adjustment to be made without having to scrap the entire project. A variable regulated power supply is a useful tool for anyone who has a background with electrical circuitry and components. It also has many uses other than just testing.

In addition to being used to test circuits, this type of power supply may be used by miniature hobbyists as well. For example, such tools are commonly used by those who work with miniature electronic train sets. The power supply can be adjusted to either speed up or slow down the train as it is pushed around the track by the power of the completed circuit (Christoph Katzer, 2008).

Another common use for this type of power supply is in the tattoo industry. Variable regulated power supplies are used every day by tattoo artists to adjust the intensity and speed of the motor on their tattoo guns in order to create the desired effect with the particular tattoo needles they are working. For instance, when a tattoo artist is outlining a new piece, the speed of the gun is increased through the power supply so the needle moves faster, creating a more consistent outline. When the artist is shading an area of the skin, the power supply is used to slow down the needle in order to create consistent color coverage within the tattoo (Christoph Katzer, 2008).

A variable power supply works by restricting or increasing the voltage delivered to the circuit from the original power source. For instance, when the electronic train hobbyist starts his train on the track, he doesn’t simply flip a switch and turn the train on full blast; rather, he delivers the voltage to the circuit in small increments through the regulated variable power supply until the desired speed of the train is reached (Cooler Master, 2008).

1.7                                                         PROJECT ORGANISATION

The work is organized as follows: chapter one discuses the introductory part of the work,   chapter two presents the literature review of the study,  chapter three describes the methods applied,  chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendation

Get the Complete Project

This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for international clients.

Click here to Get this Complete Project Chapter 1-5

You can also check other Research Project here:

1. Accounting Research Project
2. Adult Education
3. Agricultural Science
4. Banking & Finance
5. Biblical Theology & CRS
6. Biblical Theology and CRS
7. Biology Education
8. Business Administration
9. Computer Engineering Project
10. Computer Science 2
11. Criminology Research Project
12. Early Childhood Education
13. Economic Education
14. Education Research Project
15. Educational Administration and Planning Research Project
16. English
17. English Education
18. Entrepreneurship
19. Environmental Sciences Research Project
20. Guidance and Counselling Research Project
21. History Education
22. Human Kinetics and Health Education
23. Management
24. Maritime and Transportation
25. Marketing
26. Marketing Research Project 2
27. Mass Communication
28. Mathematics Education
29. Medical Biochemistry Project
30. Organizational Behaviour

32    Other Projects pdf doc

1. Political Science
2. Psychology
3. Public Administration
4. Public Health Research Project
5. More Research Project
6. Transportation Management
7. Nursing

Education

Essay 

Full Project – Design and construction of a 0-24v variable regulated power supply